Outboard Bracket & Parts. TENOB

NZD $2.65NZD $919.37

SKU: N/A Category:

Description

TENOB product. NZ made with pride. 
New Zealand’s most popular auxiliary/trolling outboard motor mounting bracket for over 36 years.
Superior construction means that it is possible to have a motor mounted on this bracket while towing your boat on the road. No parts to come loose or fall off due to use of pressed stainless steel pivots and shake-proof fasteners.
Lifetime polished marine grade 3mm stainless steel.
Ratings for Rise & Fall brackets (for both 2 and 4 stroke motors) – standard shaft, up to 25hp (18kw), long shaft up to 20hp.
Maximum motor weight of 58kg.
Uses varnished hardwood. Hardwood is an ideal material because the outboard motor clamps sink slightly into the surface, thus reducing the risk of the motor slipping off.  This cannot be achieved with plastic mounts.
Four styles available; fixed or rise & fall, each in either transom mount or platform mount.
 
(A)   OU01 – Transom Mount, Rise & Fall
 
Bracket size – 350mm (reach) x 280mm (mounting width) x 215mm (mounting height).
Hole centres – Approximately 152mm vertical x 207mm horizontal.
Vertical movement (adjustment) – 340mm (13.3/8″). 
Timber size – 260mm x 190mm x 35mm.
In its lowest position the top edge of the timber is 83mm below horizontal. 
In the second to top position the top edge of the timber is 144mm above horizontal.
 
(B)   OU015 – Platform Mount, Rise & Fall
 
Platform to top of timber – 475mm in raised position, 135mm in lowered position giving a vertical movement (adjustment) of 340mm.
Reach – 350mm.  Overall width (left – right) – 295mm.
Mounting footprint – 263mm (front – back), 280mm wide (left – right) (note that the bracket can overhang the platform up to 100mm, thus reducing the fore – aft space required).
Hole centres – Approximately 152mm vertical x 207mm horizontal.
Timber size – 260mm x 190mm x 35mm.
 
(C)   OU06 – Transom Mount – Standard, Fixed
 
Rated for 10hp or 38kg maximum (long shaft models: 8hp max.).
This version allows most auxiliary/trolling motors to tilt up without touching the transom.
235mm wide x 295mm long overall.
Side brackets are angled up ten degrees to compensate for the transom angle.
Mounting holes – 190mm horizontal x 123mm vertical spacing, centre to centre.  Four holes 11mm diameter (use 10mm (3/8″) mounting bolts).
Timber size – 220mm x 160mm x 35mm.
 
(D)   OU06S – Transom Mount – Short Version, Fixed
 
Rated for 10hp or 38kg auxiliary/trolling motor maximum (long shaft models – 8hp max.).
Suitable also for motor storage at home or on the launch due to its compact dimensions.
235mm wide x 190mm long overall.
Side brackets are angled up ten degrees to compensate for the transom angle.
Mounting holes – 190mm horizontal x 123mm vertical spacing, centre to centre. Four holes 11mm diameter (use 10mm (3/8″) mounting bolts).
Timber size – 220mm x 160mm x 35mm.
 
(E)   OU08 – Platform Mount – Standard, Fixed
 
25hp (19kw) rated, 2 or 4 stroke, standard shaft. Long shaft rating is 20hp.
280mm wide x 190mm high x 245mm long (fore – aft).
Mounting platform depth (fore – aft) required is 210mm minimum.
Height from top of timber to mounting platform – 175mm.
 
(F)   OU08L – Platform Mount – Low Height, Fixed
 
Rated for 10hp (7.5KW) or 38kg rated auxiliary/trolling motors.  For 20″ long shaft motors the rating is 8hp max.
260mm wide x 135mm high x 310mm long (fore – aft).
Mounting platform depth (fore – aft) required is 270mm minimum.
Height from top of timber to mounting platform – 95mm.
 
Spare parts for TENOB outboard motor brackets only –
(G)  OU02 – Large compensating spring – 29mm outside diameter x 147mm overall length (107mm excluding ends). For models code OU01 & OU015. Two per bracket. Sold each. (This is the standard and only compensating spring used on OU01 & OU015 brackets).  
(H)  OU03 – Spring kit contains 2 large compensating springs (OU02), 8mm bolts, nuts & spacers. For models code OU01 & OU015. This kit has two uses – a.  Fit to a bracket which has no springs b.  If the bracket is too heavy to lift because of the motor weight, then the springs can be doubled up to four.  This typically is the case for motors over 8hp. The additional springs are fitted to the outside of the bracket arms. To do this change the bolts (use the longer bolts supplied in the kit) holding the existing springs and fit the extra springs under the bolt head i.e. the bolt now holds the end of two springs.  
(I)   OU035 – Small stainless steel spring. Fits bracket handle. Two required. Sold each.   (J)   OU04 – Replacement board. Suits TENOB stainless steel brackets codes OU01, OU015, OU08. Fastens to bracket with four screws (not included). 260mm wide x 190mm high.  
(L)  OU0406 – Replacement board for OU06S. 220mm wide x 160mm high.  
(K)  OU0408L – Replacement board for OU08L.
 
Please Note: Outboard brackets are a Tenob manufactured and/or assembled part with several components. For that reason, it is not unusual for the product to show as out of stock if the assembled version hasn’t yet been entered into stock. In most cases you can check the stock level of the individual parts on this site. Please order as normal and call us if you need a live update on availability.